1. In the PUSCH power algorithm, the path loss is calculated by measuring which of the following channels?

2. How many types of system messages SI are defined in the R15 standard?

3. Which of the following modules is responsible for the selection of PCF during the PDU session establishment process?

4. In the PUSCH power control algorithm, which of the following measurement results does the gNB use to perform power control?

5. In the Option 3X architecture, which network element controls the UE-AMBR and minimum rate guarantee of the downlink Non-GBR?

6. In RAN3.0, for the mobility algorithm of SA network, how many A2 thresholds can be set on the base station side?

7. When downloading in SA networking, which event initiates the handover decision phase due to poor signal in the serving cell?

8. In RAN3.0 version, which of the following PUCCH formats does the base station not support?

9. In high frequency scenarios, what is the maximum subcarrier spacing that can be used for all channels and signals?

10. In low-frequency scenarios, how does the UE obtain the beam ID of the current SSB?

11. In the SIB1 message, if the expected preamble power is -100dBm, the SS B transmit power is 18dBm, and the current RSRP is -90dBm, what is the preamble transmit power of the first PRACH of the terminal?

12. In the drive test tool, which of the following indicators cannot be monitored?

13. During the handover preparation process, the source cell determines the target cell for handover based on which of the following parameters?

14. Which of the following parameters does not need to be configured in the command to configure the 5G external cell?

15. During uplink scheduling, what is the fixed value of the “logical channel guaranteed rate” for each non-GBR logical channel?

16. In an inter-frequency handover scenario based on frequency priority, which of the following event measurement reports is used to trigger inter-frequency measurements?

17. During the downlink MCS adjustment process, the base station makes the adjustment based on which of the following measurements?

18. During downlink scheduling, which of the following services has the highest scheduling priority?

19. Which of the following factors is not involved in calculating the number of RBs for a user in downlink scheduling?

20. Among the A3 event parameters for intra-frequency handover, which of the following parameters cannot be configured individually based on QCI?

21. When using Probe to test the NSA network, it is found that the MAC layer rate of LTE uplink is 20Mbps, but the PDCP layer rate is 0. Which of the following understandings is correct?

22. During the same-frequency cell reselection process, if you want to make it easier for the terminal to reselect from the serving cell to a specific neighboring cell, how can you modify the parameters?

23. In the uplink power control process, the power control of SRS is related to the power control of which channel?

24. In RAN 3.0, what is the minimum configuration of PDCCH bandwidth in a cell-specific BWP?

25. In the downlink channel configuration in RAM 3.0 version, what is the maximum power offset?

26. For a 60KHZ SCS configuration, how many time slots are included in a radio frame?

27. How much data does the SSB that occupies 20 RB resources carry?

28. Which parameter indicator will not be referenced in the SCell deactivation management of carrier aggregation?

29. When testing the downlink peak value of an NR network, which of the following should the PDSCH DMRS type be configured to?

30. If the MeasAndMobParametersMRDC of the terminal MR-DC capability contains the independentGapConfig information element, which GAP configuration is recommended for NR inter-frequency measurement?

31. During downlink data transmission, if the terminal suddenly fails to report CQI, what will happen?

32. For a 100MHz cell, when the downlink uses type 0 allocation, what is the minimum resource allocated in the frequency domain?

33. In downlink detection, what is the PDCCH BLER synchronization threshold Qin?

34. In the continuous CA scenario in the protocol frequency band, what is the maximum center frequency band interval between carrier 1 (60MHz bandwidth) and carrier 2 (100MHz bandwidth) in the n41 frequency band?

35. Which of the following manufacturers was the first to complete the SA functional test of the domestic IMT-2020 5G Promotion Group?

36. Which piece of information will not be referenced by the automatic deletion of neighbor relations feature?

37. Which of the following in the terminal capability report indicates that the terminal supports antennas?

38. Imbalanced terminal receiving antennas will affect RANK performance. Generally, within what range can the average RSRP difference of different antennas be considered balanced?

39. The initial TA (time advance) adjustment of the terminal is obtained through which of the following messages?

40. For the N78 frequency band, which of the following time slot ratios (downlink, uplink) can support the transmission of SSB beams?

41. Which of the following PUCCH formats does not have DMRS?

42. Which of the following uniquely identifies a user within AMF?

43. Which of the following time slot configurations is conducive to reducing the delay of air interface scheduling?

44. Which of the following networking architectures belongs to the NE-DC solution?

45. When using NR to cover high-rise buildings, which of the following is the recommended configuration for NR broadcast beam scenario?

46. In the Option 3x architecture, during the dual connection establishment process, the eNB will send an ERAB Modify IND message to the MME. The IP address carried in the message belongs to which of the following network elements?

47. Which of the following channels or signals has the same transmit power as PUSCH?

48. Among the following services, which type of service has the highest default priority?

49. Which of the following channels or signals usually uses open-loop power control?

50. The Qoffsettemp parameter is introduced in the 5G cell selection algorithm. Through which message is this parameter sent to the UE?